Maestro 3D Dental Scanner - Information and Advice
Introduction to the use of Maestro 3D Dental Scanner
This document is intended to introduce the user, in a simple and quick way, to the install Maestro 3D Scanner. Please read this manual carefully before making use of scanning software.
- Install the calinration files
- Windows Aero theme
- Screens configuration
- Problems with antivirus or firewall
- Problems with power options
- Problems with projector
- Scanner manutention
Important informations
Precautions
Please read this manual carefully before using your Maestro 3D Scanner and keep the manual handy for future reference. Your serial number is located on the rear of your Scanner. It will be necessary to specify the serial number for all comunications related to the warranty and eventual problems.
|
To turn off main power, switch off the power button located on rear of the Scanner. Only after done this you can remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
|
|
|
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. |
|
|
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
|
|
This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems. |
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS CAN BE FULLY INSERTED.
|
Disposing of your used product
|
EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes projectors and their electrical accessories or lamps. When you dispose of such products, please follow the guidance of your local authority and/or ask the shop where you purchased the product. After collecting the used products, they are reused and recycled in a proper way. This effort will help us reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human health and the environment at the minimum level. The mark on the electrical and electronic products only applies to the current European Union Member States. |
Important safeguards
Installation
Do not place the Scanner in the following conditions:
- on an unstable cart, stand, or table.
- near water, baths or damp rooms.
- in direct sunlight, near heaters or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
Maestro 3D Dental Scanner contains a projection unit. The Scanner should not be installed in any way other than the desktop, otherwise lamp life of its projection unit could decrease dramatically and the Scanner could work not properly or return incomplete or incorrect results.
Fire and shock precautions
- Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your Scanner. Allow at least 4 inches (10cm) of space between your Scanner and a wall.
- Do not try to touch the ventilation outlet placed on the back of the Scanner as it can become heated while the Scanner is turned on.
- Prevent foreign objects such as paper clips and bits of paper from falling into your Scanner. Do not attempt to retrieve any objects that might fall into your Scanner. Do not insert any metal objects such as a wire or screwdriver into your Scanner. If something should fall into your Scanner, disconnect it immediately and have the object removed by a qualified service personnel.
- Do not place any objects on top of the Scanner.
- Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
- The Scanner is designed to operate on a power supply of 120-240V AC 50/60 Hz. Ensure that your power supply fits this requirement before attempting to use your Scanner.
- Do not look into the projection unit lens while the Scanner is on. Serious damage to your eyes could result.
- Keep any items such as magnifying glass out of the light path of the projection unit. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause unpredictable outcome such as fire or injury to the eyes.
- Do not cover the projection unit lens with cap or similar while the Scanner is on. Doing so can lead to melting of the cap and possibly burning your hands due to the heat emitted from the light output.
- Do not place any objects, which are easily affected by heat, in front of the projection unit lens or a projector exhaust vent. Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the light output and exhaust.
- Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.
- Do not use any power cables than the supplied one.
- Do not bend or tug the power cable excessively.
- Do not place the power cable under the Scanner, or any heavy object.
- Do not cover the power cable with other soft materials such as rugs.
- Do not heat the power cable.
- Do not handle the power plug with wet hands.
- Turn off the Scanner, unplug the power cable and have the object removed by a qualified AGE Solutions service personnel under the following conditions:
- When the power cable or plug is damaged or frayed.
- If liquid has been spilled into the Scanner, or if it has been exposed to rain or water.
- If the Scanner does not operate normally when you follow the instructions described in this user's manual.
- If the Scanner has been dropped or the cabinet has been damaged.
- If the Scanner exhibits a distinct change in performance, indicating a need for service.
- Disconnect the power cable and any other cables before carrying the Scanner.
- Turn off the Scanner and unplug the power cable before cleaning the cabinet.
Drivers installation
| Use Windows 7 - 64 bit.
Install the chipset drivers and usb drivers of the PC motherboard. Install all Windows update available. Install the last graphics card available from NVIDIA web site http://www.nvidia.com. Don't connect the usb cable from scanner and PC before installing the drivers. |
Run Maestro.3D.USB Driver.Setup.x32.x64.exe
Every time that windows show the alert window please click on: Install this driver software anyway.
This windows can appers 3, 4 or 5 times.
After that reboot the PC.
USB connection
After that you can turn on the power back buttons.
When you connect the first time the USB cable of the scanner to the PC the operating system could show some alert windows to search the driver of some scanner's components. In this case if this windows appears, click to search automatically the drivers into the PC.
This can happen every time that you change the usb port.
| WARNING: be sure to use USB 2.0, not use USB 3.0 port |
VGA connection
Connect the supplied VGA cable to the Scanner then connect the other plug of the supplied cable to the host PC auxiliar video out. Make sure that the cable is plugged entirely in the apposite connector, then fix the security screws placed on VGA cable (both on the Scanner and PC). A cable not correctly plugged can cause the malfunction of the Scanner and can lead to incorrect results.
Some recent video cards use a DVI output instead of VGA for secondary video output. In this case use the supplied adapter in conjunction with the VGA cable.
| CAUTION: Make sure that the VGA cable is fully inserted in secondary video output of Host PC because a cable not fully inserted can cause malfunction of the Scanner. Depending of video card of host PC, in some circumstances, this is a condition not detectable by Scanner diagnostics tools. |
In the following image you can see a screenshot of connectors of a Nvidia 8600 GT Video Card. In this case you must connect the Scanner to the DVI port using the supplied DVI to VGA connector.
| IMPORTANT: when you turn on your PC make sure the VGA cable is connected to the PC and the scanner, (also with the scanner turned off).
Otherwise can happen that when you turn on your PC the Graphic Card not having a VGA cable connected with the scanner it can disable the video output. In this case need to plug the VGA cable and restart the PC. |
Device manager
From the Device Manager you can see this:
The name of the drivers may be different.
If some hardware components are not correctly installed, try to right mouse click and try to update driver over Internet.
Install the scanning software. (See the manual of the scanning software).
After that: right mouse click over scanning software icon and Properties -> Advanced -> (check) Run As Administrator.
Install the calibration files
To Install the calibration files:
copy the two xml files:
camera.calibration.xml rotary.table.calibration.xml
into the folder of the scanning software.
| IMPORTANT: each calibration is different for each scanner. |
Windows Aero theme
Use the Windows Aero theme.
Screens configuration
Set the projector (1) to the right of the main monitor with a resolution of 1024x768. The projector could be the screen with label 1 or label 2 depending of video card configuration.
Orientation: Landscape
Multiple displays: Extend these displays
Problems with antivirus or firewall
If the software freezed or the projection of the patterns is very slow, could be due to the presence of some antivirus or firewall installed on the PC. This softwares can scan and analyze the transit of information between a PC and scanner, slowing or stopping the operation of the scanner. To remove this problem and should be added "Maestro 3D Easy Dental Scan" to the list of exclusions of the antivirus or of the firwall, or unistall this software.
Problems with power options
In order to ensure that scanner works properly please check for Power options in Control Panel. Ensure that monitor it's never disabled. Below it's an example of configuration done in Windows 7 64 bit.
Problems with projector
In order to ensure that scanner works properly please verify the projector status.
Sometimes could happens that the scanning software detects that the projector is turned on when in fact this is turned off or vice versa.
This can cause problems during the scanning phase. To check that status of the projector is consistent it's necessary press the info button 
and wait that the scanning software detect the hardware status. Into the info windows it's possible to check if the status of the projector it's turn on or turn off.
Now the user should really make sure that the projector is really turned on or really tuned off.
To do this, it is enough to verify if the projector emits a light, especially if it projects the desktop background. When the projector is turned on and all cables are correctly connected from scanner and PC the projector project the desktop background image. So if you put a white paper in front the projector you must see the background image of your desktop.
