Maestro 3D Easy Dental Scan - User Manual

Introduction to the use of Maestro 3D Easy Dental Scan software

The aim of this document is to introduce the user to the use of the Easy Dental Scan Software, in a simple and quick way. Please read this manual carefully before making use of the Easy Dental Scan Software. Maestro Easy Dental Scan is the software that combines with the line of Maestro 3D dental scanners. The software allows automatic acquisition of the dental objects with one click and creation of 3D surfaces of the acquired data entirely automatic, without any user intervention. The innovative software guarantees exceptional performances, fully exploiting the parallel calculation offered by the most recent multicore and multithreading technologies available on the market.

Assembly of components

Assembly of the calibration kit

See the figure below showing how the calibration kit should be assembled once it has been extracted from its packaging.

• 1 allen key;
• 2 plate;
• 3 calibration plate;

Simply screw the 4 supplied screws to join the plate to the calibration plate. Be careful not to scratch or stain the calibration plate. It is advisable to handle the plate with gloves so as not to dirty it or leave fingerprints on it.

WARNING store the calibration kit in a place away from direct light and moisture; do not clean with solvents or acids but use only a dry cloth; scratching or dirtying the calibration plate will compromise the calibration of the scanner; handle with care using fabric gloves so as not to leave fingerprints or dirt on the calibration plate;

Assembly of the impression plate

See the figure below showing how the impression plate should be assembled once it has been extracted from its packaging.

Follow the steps as shown in the figure to correctly assemble the impression plate.

Scanning plates supplied

The image below shows all scanning plates supplied with the MDS500 scanner:

• 1 interface plate;
• 2 arch plate;
• 3 multi dies plate;
• 4 impression plate;

• 1 use this configuration to scan single dental arch or upper and lower arches in occlusion;
• 2 use this configuration to scan removable stumps;
• 3 use this configuration to scan impressions;

UAC - User Account Control

To avoid difficulties and limitations in the use of the Software, it is necessary to set the UAC slider - User Account Control to the minimum value as shown in the picture below.

To log in to the setting window: Control panel-> User Account-> Change Settings User Account Control.

Administrator's Rights

In order yo put in operation the Software it is necessary to set correctly administrator's rights.

Follow the instructions as shown in the pictures below.

Right button of the mouse on the Software's icon to start the contextual menu and select the entry properties.

Follow the steps as shown in the sequency from 1 to 4.

• Press the button Advanced.
• Select the voice Run as administrator.
• Press the button Ok.
• Press the button Ok.

User Interface

The figure below shows the composition of the user interface.

• 1) Main Toolbar.
• 2) Tree Area.
• 3) Info Area.
• 4) Bottom Area.
• 5) Visualization\Editing Area

Main Toolbar

The main toolbar allows the access to all functionalities of Easy Dental Scan Software.

• 1) New Acquisition - Start a new scan or define a new scanning strategy.
• 2) Scanner Status - Activates the window that monitors the hardware scanner status.
• 3) New Group - Adds a new group in the tree. It's possible to move the elements of the tree inside/outside a group by mouse drag and drop.
• 4) Export - Export the selected item along the Z or Y Axis. You can export in open STL file or PLY file format.
• 5) Postprocess (convert scanned data into a 3D model) - The function is enabled when an item is selected not postprocessed. This operation can take a few minutes to converts the scanned data from the scanner in a triangular geometry.
• 6) Editing filter - Edit the selected items. This is useful for removing artifacts due to scanning, to remove the putty scanned, for make the holefilling, the decimation, 2D\3D selection edit, etc.
  • Editing with 2D rectangle
  • Editing with 3D polyline
  • Editing with 2D selection
  • Holefilling
  • Decimation
• 7) Import a scanbody from library.
• 8) #Stumps_registration automatic alignment procedure of the stumps.
• 9) #Manual_3-2-1_alignment set the selected item as fixed or floating in the manual align procedure.
• 10) #3D_Comparison.
• 11) Free Measures:
  • point-point measures.
  • angle measures.

• 12) CAD - send selected items to the design software.
• 13) Projector status.
  • Power on.
  • Power off.

The calibration tab is described here: Calibration.

Bottom Toolbar

The bottom toolbar is the area of the screen containing a progress bar that is displayed and updated during each computation of the program and the controls for changing the visual settings of the visualization/editing area.

• 1) touchscreen mode (Rotate/Pan).
• 2) magnify in [Key PGDown]/magnify out [Key PGUp].
• 3) reset trackball [Key R].
• 4) parallel projection [Key O], perspective projection [Key P].
• 5) smooth shading [Key S], flat shading [Key F].
• 6) photorealistic rendering.
• 7) shadow, (available if photorealistic rendering is enabled).
• 8) texture color, (real object color).
• 9) show/hide triangles, edges [Key E], vertices [Key V].

Visualization / Editing Area and Info Area

The visualization / editing area is the area of the window in which the models are visualized and all the editing operations are performed.

In the visualization area it is possible to see the models and edit and measure distance between different point.

In order to examine the models displayed in the visualization / editing area camera parameters (position, scale and rotation) can be setted using an instrument called trackball.

The trackball is very simple to use. Just use the Left mouse button dragging to rotate around the model, the mouse wheel to Zoom in / Zoom out and the Right mouse dragging to move (pan) the camera.

The info area of the screen shows the info related to the current item.

Tree Area

The Tree Area contains all the models scanned. The Tree Area organization has a tree. The use of groups allows you to keep an ordering of the models scanned. To select a model from the Tree Area just click on it with the left mouse button. The models selected will be displayed on Visualization Area. To select more models click by holding down the CTRL\SHIFT key.

The Tree Area can contain the following elements:

	Stump
	Upper Jaw
	Lower Jaw
	Upper\Lower Gingiva
	Upper\Lower Waxup
	Maxillary\Mandibular Relationship
	Rangemap
	Group

For each of these elements there is associated a set of operations accessible via enabled icons in the Main Toolbar. These allow the user to access the main functions of the software.

By accessing the drop-down menu as shown in the following figure, you can import into the tree the STL file.

Target objects

Some examples of target objects:

• Maxillary and Mandibular relationship

• Upper-Lower Jaw

• Other examples of dental arch

• Impression

• Stumps

Proper positioning of objects

Arch or MMR

In the following images the correct positioning of the models on the rotary table is showed. The image below shows an arch correctly positioned on the rotary table. The arch should be placed at the center of rotary table supported by the putty or any other adhesive that keeps it well anchored to the table.

The arch should be parallel to the surface and should not be tilted.

• 1 interface plate;
• 2 arch plate;
• 3 object to scan, arch or maxillary mandibular relationship (MMR);

Multi dies

It is possible to put on the rotary table of the scanner more stumps simultaneously. See the following pictures to observe the proper placement of stumps. After the scanning process, the software automatically recognizes and separates the individual stumps, adding an item in the Tree Area for each acquired stump. The pictures below show how to correctly place the stumps on the rotary table of the scanner. The scanner may be equipped with a multidie plate of 8 teeth.

• 1 interface plate;
• 2 multi dies plate;
• 3 stumps;

The numbering (1..8) on the plate meets the numbering of the elements added to the Tree Area only if the plate is placed in front of the scanner. When working with more than a stump it is absolutely necessary that adhesive putties sustaining stumps and the body of each stumps will be separated at least some millimeters from each other. In this way the scanning software is able to recognize each stump, see the correct stumps position in the picture below:

An example of incorrect positioning:

WARNING Shown in the picture above an incorrect positioning of the stumps. The support of the putty of each stumps should not join and the bodies of the stumps shall not touch or should not be too close because this incorrect positioning prevents the scanning software to identify and separate the individual elements.

TIP The stump/s should not be placed with an excessive inclination, because the scanner is not able, in these conditions, to acquire all the margin line. So you should always place the stumps perpendicular to the rotary table surface.

Impression

The following images show the correct positioning of the impressions on the rotating table. This fixing system, used in conjunction with the Smart Impression Scanning feature, is only available for MDS 500 models. The image below shows an impression correctly positioned on the rotating table. The impression must be attached to the special clamp so that it is in the center of the rotating table. You can also use the wheel to adjust the angle.

It is not necessary to use other plates, the impression fixing system must be positioned directly inside the scanner.

TIPS the impressions must be dry; it may be necessary due to the impression material, to opacify it with special scanning sprays; it is recommended to cut from the impression any unnecessary excess material that could cause areas of shade; take care to position the impression so that it is in the center of the plate and with the right inclination;

3D Scanning

Scan parameters

To start a new acquisition just press New acquisition in the Main Toolbar.

Through this window you can choose the type of object to be scanned and the scanning parameters.

• 1 object type (arch, gum, waxup, stumps, impression, maxillary-mandibular relationship, ...).
• 2 scanning Strategy: it's possible to choose a scanning strategy.

WARNING It may happen that with a low number of acquisitions (eg 4-5) for certain models may fail to scan because there is not sufficient overlap geometry between the various shots. In this case it is sufficient to increase the number of acquisitions into the strategy.

• 3 upper or lower model.
• 4 faces (triangles):

This number defines the number of triangles you want in your final model. The figure below shows the same model with 45000, 10000 and 2500 triangles. The precision and accuracy in the 3 models is equivalent. Among the 3 models changes the number of triangles that approximate the surface geometry. The system acquires always at max precision and max accurancy. Only after obtaining the final three-dimensional model at max number of triangles, it is decimated to obtain the desired number of triangles. Is also possible to decimate the model later.

WARNING Greater is the number of triangles, greater is the size of the STL file. 30000 triangles-> 1,42 MB STL file. 45000 triangles-> 2,14 MB STL file. 250000 triangles-> 11,90 MB STL file.

Recommended values:

Arch\Gum\Waxup\Impression	180000 - 250000 triangles
Stump	15000 - 45000 triangles
MMR	180000 - 200000 triangles

• 5 height of interest:

This param allows you to choose the height of interest of the model, (this height value is measured starting from top to bottom).

First picture (from left to right) shows the model of a stump where the height of interest parameter is disabled and then the stump is acquired entirely including the adhesive putty support that sustains it. Subsequent images display the same stump with the height of interest parameter set at 20 mm and 15 mm respectively (as can be seen the adhesive putty support is automatically removed).

It is important to remember that, in order to make the best use of this parameter, the model (arc, one or more stumps, etc...) must be placed perpendicular to the surface of the rotary table.

IMPORTANT Cut the model choosing the height of interest reduces the computation time of postprocessing and can improve the quality of the results. (Especially a smaller volume of the point cloud of the stumps can lead to a better yield of the final model).

In any case, you can always remove the not interesting geometry, at any time, by editing the model.

• 6 texture Color Superimposition:

This requires the Texture Color Superimposition module active. The activation is carried out through a software license. This is useful to obtain models with a RGB color texture or grey scale color texture. For example it helps create very accurate margin lines as marked on the model.

• 7 close base:

If this option is checked, the software close the bottom base of the model automatically.

• 8 postprocessing (convert the data acquired in a 3D model):

If this option is checked, the system automatically postprocessing the data acquired and it builds the triangular geometry surface. If it is not checked the data will be not postprocessed. It is possible postprocess the data acquired later.

• Good (fast): this option is recommended.
• Best (slow): this option take more computation time and make a 3D models with more details.

TIPS To reduce the time of interaction with the scanner, where you have many models to be scanned is advisable not to make the postprocessing after each scan. In this case it is recommended scan all model (not check the option "Postprocessing", no check the option "Turn off") and at the end of the work, turn off the system and select from the tree area all items (rangemaps) and press button to postprocess all models.

• 9 cameras resolution, (available only with MDS 500 model scanner).

• 10 play sound after scan:

It's possible to choose a *.wav file to play after the scan and after the postprocessing.

• 11 turn off the system after the scan:

Turn off the system after the end of the scan.

TIPS Remember to turn the system off when not in use to avoid wasting the lamp.

Scanning process

This window shows the progress of the scanning phase. This may take a few seconds or a few minutes depending on the strategy chosen. In the window on the left shows the 2D image acquisition and 3D image on the right.

After this operation, if the the option "Postprocessing" was checked the software automatically generates the surface of the model from the acquired points, and adds to the Tree Area a new element. Then selecting it in the Tree Area, the model is displayed into the Visualization Area.

If the option "Postprocessing" was not checked, the software adds to the Tree Area a new element with a greyscale icon. Before you can perform any operation of this model is necessary to postprocess the data acquired.

WARNING Before scanning make sure that the model is correctly positioned on the rotary table and that the front door of the scanner is closed. During the scan please don't move neither the scanner nor its support plane.

Scanning Strategy

The following image shows the window for managing the scanning strategies.

See below for details:

• 1) Scanning group: MMR, Arch, Stumps, Impression.
• 2) Strategy name.
• 3)
  • New Strategy.
  • Save current Strategy.
  • Delete current Strategy.
• 4) Add tilt command (before adding the command selects the rotation degrees).
• 5) Add rotation command (before adding the command selects the rotation degrees).
• 6) add a batch acquisition. (before adding the command select the number of rotary table steps of the rotary Axis).
• 7) Commands:
  • Clear all commands.
  • Delete selected command.
  • Add tilt home position command.
  • Add rotation home position command.
  • Add an alignment group.
  • Add a single acquisition.
  • Start the strategy simulation.

TIPS: Each alignment group should contain more than one acquisition. Each subsequent acquisition must have an ​​overlap area with the previous. Each alignment group must have an ​​overlap area with the previous. The software aligns each acquisition within each group and then aligns groups. By default each strategy start and ending with tilt home position and rotation home position.

Impression Scanning

The following image shows in detail the parameters to be selected to scan the impression:

• 1 select impression from the drop-down menu and choose the rest of the parameters as you prefer.

Preliminary to this, see the correct positioning of the impression on the appropriate impression plate: #Impression

The image below shows the next step.

In this phase the tilt motor must be adjusted so as to be able to visualize the impression as shown in the image above. The goal is to give the software an excellent point of view, for example, that the incisors are clearly visible, both vestibularly and lingually. From this starting point the software will build a dynamic scanning strategy that allows the best possible acquisition of the impression. Try to adjust the inclination value so that the incisors are visible as much as possible. Let's see in detail the interface tools:

• 1 press the button + or - to move the tilting axis;
• 2 select this if you want to use the best strategy. This takes more time but guarantees greater coverage;

CONSIGLO: the optimal inclination values must be in a range between -40 and 0. If this interval was not sufficient, use the manual wheel of the impression plate to give an auxiliary inclination; tighten the manual wheel of the impression plate to prevent it from moving during the scanning phase;

The next step as shown in the image below is the scanning phase. During this phase it is important that the scanner door is closed so that the ambient light does not interfere, reducing the contrast of the structured light. It is equally important that the scanner be placed on a stable table and that it will not be shocked or vibrated during this phase.

Once the impression scan is complete, the software allows you to "clean up" the scan before processing it. See also the function of #Editing_with_2D_selection. In this phase, as shown in the image below, it is possible to remove all the excess parts of the scan.

In this way, the post-processing phase that converts the point cloud into a 3D model will be faster and more effective.

Below you can see the finished result of the impression scan:

photo of the real impression

Stumps registration

The registration of stumps is totally automatic and it allows to replace the low resolution stumps, acquired with the arch, by the high resolution stumps acquired without the arch.

Select into the Tree Area the arch with the stumps (which are to be replaced).

After the arch is displayed in the Visualization Area with a constrained view so that it can be inspected only from above. In details:

• 1) to add the stumps\scan body to substitute, select these from tree area and press the buttons.
• 2) if replace stumps is checked, the high resolutions of the single stump will be replaced with the lower resolutions stump scanned with the arch. This is recommended if you need to work with a dental cad software. If not select this option the stump will be only aligned.
• 3 if this option is checked the software make a backup copy of the data.
• 4) preview area of the stumps.

TIP: If the selected stump is not the correct stump, just close the preview window to remove it from the registration process. You can register up to 16 stumps simultaneously.

After having selected and added the stumps, press double click with the left mouse button over the center of the head of the low resolution stumps to indicate the position where every stump must be registered.

By double clicking over the head of the stumps, it is added to the Visualization Area a sphere (called marker) associated with a number. Color and number, as shown in the picture, these are associated with the right stump.

TIP: To remove a marker double-click on it.

Before to proceed with the registration, please make sure that each marker is associated with the right stump. To proceed with the registration press the Next button.

A progress bar placed in the Bottom Toolbar will indicate the progress of the registration process.

At the end of the registration process the result of the registration is displayed in the Visualization Area, where low resolution stumps have been replaced with high resolution stumps. If you are satisfied with the result press the button Next to finish and save the registration obtained or press the previous button to return to previous step.

If one or more stumps are not correct aligned, press the close button near the marker and then after having completed this task you can re-register only those stumps.

If the registration is not satisfactory, please verify that markers have been placed in the correct position as explained previously (in the center of the head of each stump and in the correct order).

TIP: It is also possible substitute the stumps on the arch with a manual alignment.

Manual 3-2-1 alignment

With the manual registration process, is possible to align any pair of models. For example useful to align a stump on an arch or an arch or bite with a antagonists reference model.

To align two models, need to select the fixed model (example maxillary mandibular relationship) and the floating model (example arch). The next image shows the manual alignment window.

To align the floating object over the fixed object, you have to add some points in the fixed model (that appears to the left of the screen) and the same points should be added to the floating object (that appears to the right of the window). You must add at least 3 points on each model.

• 1) clear fixed or floating point.
• 2) fine alignment. Improves the initial alignment given by the points entered by the user.
• 4) preview area where are showed the fixed and floating model.
• 5) alignment result.

TIP: Press double click with left mouse button to add a point over the model.

Editing Filters

Editing with 2D rectangle

Editing features of the rectangular selection. The image below shows the filter window.

Holding down the SHIFT key and the left mouse button you can draw a rectangular selection area. The area of ​​the selected geometry will appear colored red. In the toolbox on the left side of the screen there are buttons to delete the selected area, invert the selection, clear the selection. To save the changes and return to the previous screen, press the button Next.

Editing with 3D polyline

Editing features of the 3D polyline selection. The image below shows the filter window.

Holding down the SHIFT key and the left mouse button you can draw a 3D polyline over the model. This function is useful to remove the gum or the waxup from a model. After you have drawn the polyline just double click into the area that you want to delete. The image below shows the result of the filter.

To save the changes and return to the previous screen, press the button Next.

Editing with 2D selection

Editing features of the 2D selection. The image below shows the filter window.

Holding down the SHIFT key and the left mouse button you can draw a 2D selection area. The area of ​​the selected geometry will appear colored blu. In the top of the screen there are buttons to delete the selected area, invert the selection, clear the selection. To save the changes and return to the previous screen, press the button Next.

Holefilling

Editing feature of holefilling. The image below shows the filter window.

Just press the button Hole filling in the toolbox on the left side of the screen to filling all holes in the model. This is useful to fill the bottom of the base of a model. The image below shows the result of the filter.

To save the changes and return to the previous screen, press the button Next.

Decimation

Editing feature of decimation. With this feature it is possible to reduce the number of triangles of the model. The filter removes more triangles in the model areas with less features, keeping better details in the most important areas of the model as the margin line or the teeth geometry. The image below shows the initial model at 700,000 triangles:

Just choose the triangles number and press the button Decimation in the toolbox on the left side of the screen to reduce the number of triangle of the model. To save the changes and return to the previous screen, press the button Next.

The image below shows the same model with a quarter of resolution, 160,000 triangles. As you can see, there is no loss of detail and the margin lines are still very visible and detailed.

we can see that even at low resolutions as shown in the image below, of about 80,000 triangles the quality of the 3D model is still appreciable.

3D Comparison

To perform the model comparison it is possible to select the "reference" model and the "test" model. The following image shows the 3D comparison performed on two different scans of the same model. As can be appreciated from the color map, the two models are practically identical.

TIP: before comparing two models it is necessary that they are aligned one on the other, through for example the function of #Manual_3-2-1_alignment.

Free Measures

In order to perform the measures of length or angles, select the item to inspect and then goto in measures feature.

TIPS: double-click with left mouse button to add a point.

Scanner Status

Through this function, you can monitor the status of the scanner hardware. The window will show the status of each hardware device inside the scanner.

Dental Studio - Ortho Studio module Wizard

This scanning wizard helps the user to make all necessary scans and alignments to obtain a complete case to work into Dental Studio software - Ortho Studio module.

The following image shows the first step of the scan. In this phase you can scan maxillary and mandibular relationship. In this window you can change the scanning settings and the scanning strategy.

The following image shows the result of the maxillary and mandibular relationship. Now the user can scan the lower arch.

The following image shows the result of the lower arch. Now the user can scan the upper arch.

The following image shows the result of the upper arch. Now it's possible to perform the alignment of the upper and lower arch respect to the relationship. The procedure of alignment is the Manual 3 2 1 Alignment.

After that the scanning software send the correct data to the Ortho Studio software.

Dental Restoration Wizard

This scanning wizard helps the user to make all necessary scans and alignments to obtain a complete case to work into all dental cad integrated with Maestro 3D Scanner. All Maestro 3D scanners are fully integrated with leading design software such as exocad and Maestro_3D_Dental_Studio_-_User_Manual#Dental_restoration_.2F_Dental_CAD. The following image shows an example of a wizard step of the scan. In this window you can change the scanning settings and the scanning strategy.

Exocad Wizard

To integrate the scanner with the exocad software you need to edit the file \exocad-folder-installation\DentalDB\config\defaultsettings-db.xml as shown in the figure below.

<DataStoragePath>C:\CAD-Data</DataStoragePath>

...

<StartButtons>

<Button>

<Icon>ScanIcon</Icon>

< caption > Maestro 3D Dental Scanner < /caption >

<ExecPath value="C:\Program Files\Maestro Easy Dental Scan\Easy.Dental.Scan.exe">

<Params value="exocad?C:\Program Files\exoCAD\DentalCADApp\bin\DentalCADApp.exe?%p"/>

</ExecPath>

</Button>

...

• <ExecPath value = is the path where you have installed the Easy Dental Scan.
• <Params value = is the string exocad? and the path where you have installed dentalCADApp with ?%p at the end of the string.

Calibration

Calibrate a scanner model that is earlier than MDS500

Maestro_3D_Dental_Scanner_-_Calibration

Calibrate the MDS500

Click on the tab Calibration, place the calibration sample in the scanner and press the button Connect and once the images of the two cameras appear as shown above, press the button Calibration.

The calibration process is totally automatic, during this operation the optics, the motors and the relative axes are calibrated. Wait until a successful or error message appears on the screen. After this you can remove the calibration sample, store it and continue with the scans.

The calibration process takes a few minutes. It is advisable to keep the door closed during the calibration process and not to hit the table where the scanner is housed.

What is calibration?

In a 3D scan system, calibrate a camera means extract the position of the ground plane in the chosen reference and a serial of parameters, necessary to the following elaboration. These parameters are called intrinsics and they are:

• focal length (fo)
• image center (cc)
• radial distortion factor (k)

As told before, the goal of the camera calibration is to estimate the intrinsics parameters (focal length, image center and radial distortion factor) and to identify the position of the ground plane in the solidal reference with the camera.

Cameras calibration is a basic procedure to extract metric piece of information from 2D images. A camera is usually represented by the central projector model pinhole camera. This model is defined by two parameters:

• Intrinsic parameters (from three to five): they describe the camera independently from their position in the space.
• Extrinsic parameters (six): they describe camera position in the space, independently from their internal features.

This model must be conveniently correct to consider optical distortions introduced by camera lenses. The use of this kind of lenses, introduces a distortion which is necessary to balance before making a whatever calculation.

In literature there are several models to describe this kind of phenomenon. The model which has been studied and developed by Maestro 3D, estimates the lenses distortions in order to obtain a calibration which allows an excellent attention in the scanning process.

To calibrate a camera we could use the following way: focus on a chessboard whose dimensions are known, which is situated on the ground plane. From its examination, it is possible to obtain all the necessary piece of information.

How can I understand if my Scanner is not calibrated?

The main indicators of a non calibrated Scanner are clear disalignments on the surface, in the scanning process result.

In case of a bad calibration of the Scanner, it could be possible to see an error message of this type The object has moved during the Scanning process.

The picture here below, shows the same object, on the left we have a scan with a Scanner perfectly calibrated, while on the right a scan with a Scanner non-calibrated.

How many times it is necessary to calibrate the Scanner?

The quality of the materials and the solidity of the structure permit not to calibrate very often the Scanner if it has used correctly.

Nevertheless, excessive jump in the temperature or bad hits, could damage the machine and make the calibration necessary.

Small disalignments and imperfect calibrations are not evident on the final result, for this reason it is recommended to make the Scanner calibration every 1 month.

FAQ

How can I see the Software version and the dongle serial?

From the menu of the main window, tap on the enter ? -> About.... The image below shows the About window of the Software. In this window there is the dongle serial (tap on the adjacent key to copy it in the clipboard) and the version number Build

• 1) Dongle Serial.
• 2) Copy Dongle Serial into Clipboard.
• 3) Software Build Release version.

How can I see if my Software version is updated to the last available?

From the main menu tap on the entry File -> Check for updates.

How can I know which modules are active?

From the main menu tap on the entry File and tap on the entry Activate for each available module. Here, a message that will show if the module is active will appear; otherwise a window to import the license file that will activate the module in case it is not, will open.

How can I make a backup of all the scans?

Just make a copy of the folder where the software saves all scans. By default the folder is c:\MaestroData\.

The software is very slow on startup, what can I do?

If the software is very slow on startup, the cause is probably that the save folder (by default c:\MaestroData\) contains many scans. Just empty the folder or delete it completely and restart the software.

How can I change the save folder?

Edit the file application.settings.xml which is located in the installation folder of the software and change the string MaestroFolderData="c://MaestroData". To restore the settings with default value, just delete the file application.settings.xml and restart the software.

Metal parts can be scanned?

Yes it's possible but in order to improve scanning of metal parts you must use a scanning spray. In the market there are a lot spray but we advise the [Vacalon quickcheck spray].

Perchè lo scanner Maestro 3D è chiuso in dentro uno chassis e non è aperto come molti altri?

La scelta di mantenere lo scanner chiuso in un apposito chassis anzichè lasciarlo completamente aperto come è il trend del momento, è una scelta dettata dalla nostra filosofia aziendale. Maestro 3D percorre una strada di crescita tecnologica in cui l'obiettivo resta quello di ottenere i migliori risultati possibili, in termini di accuratezza, precisione, risoluzione e ripetibilità dei modelli 3D scansionati.

La tecnologia su cui si basa il sistema Maestro 3D è una variante avanzata della luce strutturata. La base di questa tecnologia è la proiezione di speciali frange luminose sull'oggetto da scansionare. Le telecamere acquisiscono centinaia di immagini in cui gli algoritmi vanno ad individuare il passaggio della frangia luminosa dal bianco al nero. In altre parole si va cercare il bordo di ogni singola frangia luminosa.

Per fare questo ed individuare questi bordi con precisione sub-pixel è necessario un elevatissimo contrasto di luce fra il bianco ed il nero. È del tutto evidente che avere uno scanner senza chassis, completamente aperto, riduce drasticamente questo contrasto. La luce ambientale incide riducendo pesantemente il contrasto della luce proiettata. Minore è il contrasto minori saranno i livelli di precisione ed accuratezza raggiungibili.

Per questo motivo Maestro 3D ha deciso di perseguire nella scelta di racchiudere e proteggere lo scanner da uno chassis chiuso in modo da eliminare qualunque influenza della luce ambientale.